Farmers Coop Assoc. FCA Keota - Executive Summary |
|
Risk Management Plan - Executive Summary Facility: Farmers Co-Op Association, FCA Keota, IA Contact: Terry Clark Phone: 319-456-6141 1. Facility Policy. The owners, management and employees of Farmers Co-Op Association (the facility) are committed to the prevention of any accidental releases of anhydrous ammonia and propane. If an accidental release should occur, the facility is prepared to work with the local fire department, or other authorities, to mitigate and minimize the impacts of the release to the people and the environment. 2. Facility Information. The primary activity at the facility is the storage and blending of fertilizers for sale to farmers. Anhydrous ammonia is received, stored and distributed for both direct application and for blending into mixed-grade fertilizers for crop production nutrients. Anhydrous ammonia and propane are stored at the facility in four storage tanks 11,000 gallons and 26000 gallons for ammonia; 30,000 gallons and 11,800 gallons f or propane. The maximum quantity stored would be 157,250 pounds for ammonia and 131,461 pounds for propane. 3. Worst-Case Scenario and Alternate Release Scenario a. Anhydrous Ammonia- The worst-case scenario would be the release of the total contents of a storage tank released as gas over a period of 10 minutes. The maximum quantity released would be 157,250 pounds, which represents the volume of the largest storage tank at 85 percent capacity as limited by design standards. The distance to the end point (point of dispersion to 200 parts per million, or ppm) is 2.4 miles. Propane-The maximum quantity released would be 132,100 pounds. The distance to the end point (point of 1 psi overpressure) is 0.4 miles. b. The alternate release scenarios, based on the five-year accident history (or the most likely potential incident), is as follows: Anhydrous Ammonia- The alternate release scenario is a release from a break in a 3-inch transfer hose followed by release of ammoni a for 2 minutes before an automatic or manual shut-off intervenes and stops the flow of ammonia. The maximum quantity released would be 110,500 pounds. The distance to the endpoint (point of dispersion to 200 ppm) is 1.6 miles. Propane- The alternate release scenario is a release from a hose rupture caused by a pull-away and assumes a 25-foot length of 4-inch transfer hose. The active mitigation devices are assumed to function as designed, limiting the release to the contents of the hose. The maximum quantity released would be 94,400 pounds. The distance to the end point (point of 1 psi overpressure) is 0.4 miles. 4. Accidental Release Prevention Program The facility has been reviewed for general compliance with the provisions of "Safety Requirements for the Storage and handling of Anhydrous Ammonia, K-61.1", published by The American National Standards Institute, Inc. (ANSI), and the standards of the U.S. Occupational Safety and Health Administration (OSHA), 29 CFR 1910.111, "Storage and handling of anhydrous ammonia". The ANSI Standard has been adopted by reference by Iowa Administrative Code Part 21-Chapter 43-Rule 43.6(200)-Standard for the storage and handling of anhydrous ammonia. The applicable standard for propane is NFPA-58. The OSHA standard is referenced in the Registration Form Section 8.3.b. 5. Five-Year Accident History. There have been no accidental releases of anhydrous ammonia or propane in the past five years that: have caused any deaths, injuries or significant property damage at the facility; nor to our knowledge, have resulted in off-site deaths, injuries, evacuations, sheltering in place, property damage, or environmental damage. 6. Emergency Response Program. The facility has: a. a written action plan, in accordance with OSHA standard 29 CFR 1910.38; b. provided state and local authorities with the emergency planning and community right-to-know information as required under SARA Title III (EPCRA); c . a written emergency response program, in accordance with OSHA standard 29 CFR 1910.120, including pre-emergency planning and employee training. 7. Planned Changes to Improve Safety. Safety improvement is an on-going process at the facility. Periodic evaluations are performed to assess the maintenance of safe conditions. There are no additional specific safety recommendations regarding storage or use of anhydrous ammonia and propane for implementation at this time. |